Prepare and test your skills

Prepare and test your skills

Free sample question with answers and detailed explanation below. The Professional Cloud Network Engineer practice bank has an additional 2,437 practice questions.Try 10 free realistic questions: instant score, no credit card, and no account required.
Your organization is connecting a Google Cloud VPC network in us-central1 to an on-premises data center with two separate peer VPN gateway devices (each with one external IP address) that support BGP and inspect traffic through a stateful firewall. Your design must meet these requirements:
Which VPN topology and routing configuration should you implement?
TWO_IPS_REDUNDANCY and two tunnels. Configure dynamic BGP routing on Cloud Router with identical advertised route priorities, and advertise identical MED values per tunnel from the peer gateways for active-active ECMP routing.Configuring a single HA VPN gateway with identical Cloud Router advertised route priorities and identical peer MED values enables active-active Equal-Cost Multipath (ECMP) routing. In this mode, Cloud Router imports both BGP routes with equal priority into the VPC routing table, and both the VPC and the peer gateways load-balance egress packets simultaneously across both IPsec tunnels.
This configuration would be appropriate if the organization prioritized maximum aggregate throughput over consistent failover bandwidth, did not rely on stateful inspection across independent peer devices, or deployed multiple HA VPN gateways where active-active routing is recommended.
TWO_IPS_REDUNDANCY and two tunnels. Configure dynamic BGP routing on Cloud Router with unequal advertised route priorities, and advertise different MED values per tunnel from the peer gateways for active-passive failover.A single HA VPN gateway provides two independent interfaces (interface 0 and interface 1), each automatically assigned an external IP address from separate address pools. When paired with an external VPN gateway resource configured for TWO_IPS_REDUNDANCY, each Google Cloud interface connects via an IPsec tunnel to a separate physical peer VPN gateway. Using Cloud Router with Border Gateway Protocol (BGP) in an active-passive configuration, one tunnel serves as the primary forwarding path while the second remains established as a hot standby.
10 and 20) on Cloud Router and unequal Multi-Exit Discriminator (MED) values from the peer gateways, all traffic traverses only the primary tunnel during normal operations. If that tunnel fails, the standby tunnel absorbs the exact same bandwidth capacity without halving throughput or dropping packets.Unlike active-active Equal-Cost Multipath (ECMP) on a single gateway, active-passive routing guarantees predictable bandwidth during failover and preserves flow symmetry for stateful firewalls. Compared to Classic VPN or multi-gateway designs, a single HA VPN gateway is the lowest-cost, lowest-complexity architecture that still achieves a 99.99% SLA.
10 and 20) to enable active-passive failover.A Classic VPN gateway (target-vpn-gateway) provides a single interface and a single external IP address using static routing (either policy-based or route-based). Because Classic VPN cannot connect two tunnels from one gateway to the same peer topology for full gateway redundancy and does not support dynamic BGP routing, achieving gateway-level redundancy requires deploying two separate Classic VPN gateways with manually configured static routes and unequal priorities (10 and 20).
20) only when the primary tunnel drops.Classic VPN with static route-based routing would be the appropriate choice if the on-premises peer VPN devices did not support BGP and an availability SLA of 99.9% was acceptable.
Deploying two HA VPN gateways across four tunnels creates multiple parallel paths between the Google Cloud VPC and the on-premises peer gateways. When configured with unequal advertised route priorities and unequal MED values such that each gateway carries one active tunnel and one passive tunnel, the design attempts to replicate active-passive failover across multiple gateways.
Deploying two HA VPN gateways would be optimal if the organization needed more than two tunnels for higher aggregate bandwidth (such as scaling beyond two-tunnel throughput limits) and configured active-active ECMP routing across all tunnels rather than active-passive pairs.
Answer them yourself and get your score the moment you finish. No account needed.
Full access includes
Keep the momentum going with these hand-picked practice scenarios
Last updated Validated